Spring cleaning to clear out some things I don’t need to get some more things I don’t need, but hope I will use more. I meet at Sportsmans Warehouse in Centennial. I am off on Wed, Thurs, and Fri and work long hours the other days so I would have to meet at 7:30PM or later Sat-Tues.
*Normally I am not available on Tuesdays, but today (5/10) I am available to meet.
Trades: A like-new Glock 19 Gen5, .300BLK ammo (brass case only-super or sub), .45ACP ammo (brass case large primer only), B&T GHM45 magazines, or a B&T GHM stock/brace.
Aero Precision Complete 5.56mm Rifle Upper
This is a really sweet AR upper that has been used exactly once for 120 rounds total. This is a custom build I did myself, but I am no half-___ builder. I have done a lot of these.
-I use a proper upper block that provides full support to the upper.
-The barrel headspace was properly gauged.
-The barrel nut was torqued to spec (35-60ft/lb for the Atlas) and timed perfectly. Many say this is not necessary with the atlas handguards but I disagree and so does Aero, so I always take the time to shim these to perfect timing and torque.
-All roll pins/coil pins are properly installed with roll pin starters and roll pin punches
Build sheet:
-Aero Precision upper receiver
-Aero Precision Atlas S-One 15” M-Lok Handgaurd
-Ballistic Advantage Modern Series Barrel machined for pinned gas block. Mid-length gas system, 4150CMV steel.
-Ballistic Advantage low profile gas block pinned to barrel for ultimate reliability
-VG6 Gamma muzzle brake/compensator (warning: It's loud!
)
-BKF gas tube secured with stainless coil pin (superior strength and gas seal to common roll pins)
-Toolcraft Nitride BCG
-Strike Industries ARCH-EL charging handle (not a fan of most SI products but these are smooth)
Sold
Ballistic Advantage 10.3” BA Hanson barrel and low profile gas block
Perfect barrel for your next AR pistol or SBR build! Brand new in package! 10.3 is just enough length for the 5.56 to achieve the velocity needed to tumble and fragment at close range so for me this is the shortest barrel I use.
-These have a 1” accuracy guarantee from BA
-4150 CMV steel
-Nitride finish. Tough finish with easy cleaning
-Nickel Boron plated barrel extension for better feeding and wear resistance
-M4 feedramps
-Carbine gas system
-HPT and MPI tested
-1:7 twist
-Pinned low profile gas block
Sold
*Normally I am not available on Tuesdays, but today (5/10) I am available to meet.
Trades: A like-new Glock 19 Gen5, .300BLK ammo (brass case only-super or sub), .45ACP ammo (brass case large primer only), B&T GHM45 magazines, or a B&T GHM stock/brace.
Aero Precision Complete 5.56mm Rifle Upper
This is a really sweet AR upper that has been used exactly once for 120 rounds total. This is a custom build I did myself, but I am no half-___ builder. I have done a lot of these.
-I use a proper upper block that provides full support to the upper.
-The barrel headspace was properly gauged.
-The barrel nut was torqued to spec (35-60ft/lb for the Atlas) and timed perfectly. Many say this is not necessary with the atlas handguards but I disagree and so does Aero, so I always take the time to shim these to perfect timing and torque.
-All roll pins/coil pins are properly installed with roll pin starters and roll pin punches
Build sheet:
-Aero Precision upper receiver
-Aero Precision Atlas S-One 15” M-Lok Handgaurd
-Ballistic Advantage Modern Series Barrel machined for pinned gas block. Mid-length gas system, 4150CMV steel.
-Ballistic Advantage low profile gas block pinned to barrel for ultimate reliability
-VG6 Gamma muzzle brake/compensator (warning: It's loud!
)-BKF gas tube secured with stainless coil pin (superior strength and gas seal to common roll pins)
-Toolcraft Nitride BCG
-Strike Industries ARCH-EL charging handle (not a fan of most SI products but these are smooth)
Sold
Ballistic Advantage 10.3” BA Hanson barrel and low profile gas block
Perfect barrel for your next AR pistol or SBR build! Brand new in package! 10.3 is just enough length for the 5.56 to achieve the velocity needed to tumble and fragment at close range so for me this is the shortest barrel I use.
-These have a 1” accuracy guarantee from BA
-4150 CMV steel
-Nitride finish. Tough finish with easy cleaning
-Nickel Boron plated barrel extension for better feeding and wear resistance
-M4 feedramps
-Carbine gas system
-HPT and MPI tested
-1:7 twist
-Pinned low profile gas block
Sold
Last edited:
